Bill Schultz's Journal

Rear Mounts And Cross Member Install

Sun, 26 Nov 2017 20:38:59 -0600

Bill Schultz's Journal --

While its fairly fresh in my mind, I want to list how I installed the Rear Mounts and Cross Member on the '74. The engine I put in is a '75 as the original engine is seized. Will be rebuilt in a year or two. Anyway, I cruised this site, the Bentley, The Haynes, YouTube and Googled every bit of info I could find - John Twists info on the variations was very helpful) - because of the posts on this site indicating it is a bear of a job. As it proved to be. Yes, after doing it a few times like others on this site, I can see were, with some exaggerating, it can be done in 30 minutes. So, lucky for me, my buddy I purchased some carb parts for for my previous B, over in Dartmouth, posted photos of his install right when I needed it. There was another person who had posted his version of the sequence of attaching the parts with a different sequence. Well, I tried both variations and only got so far before one part or another would just not pop in or access to the bolts was impossible. So, Here is how I did it... First, I DID NOT remove the exhaust system. Second, I DO NOT have a lift or a garage. So, like many of us, i was working on my back in the drive way with the car on jack stands about 15 to 18 inches up. Those are both items you should consider changing...at least a lift... Ok, so, I cleaned and painted all the reusable parts. I assembled the butterfly top and bottom with the new bushing and bolt. I bolted to transmission with the butterfly, ears to the rear, very loosely. I had the new mounts in place also. I fit the cross member in place, having to use a shovel between the frame and the exhaust pipe, lifting up on the shovel handle, gave me an inch or so to get the cross member back in place with some wiggle room. I DID drill socket size holes in the cross member, as described on this site, for easier access to the mount studs. I had tried every position and combination previously and with the car NOT on a lift and the exhaust in place, its the only way I could install. So with the cross member moved into position and loosely attaching the two bolts to the captive nuts in the butterfly, I got the left side mount stud, into the cross members bracket. (rear hole - not OD transmission so the cross member has to be closer to the trans. If OD trans, use the front hole). I thought it would be a simple matter of positioning the cross member on the right side,..but... I've seen photos of cross members which have slots in the bracket that bolts to the stud in the back of the rubber mounts, I believe individuals do this to ease the positioning of the stud into the hole(s). I do not think any cross members came from the factory with such slots. So, I trying to wiggle, pull,loosen bolts already tightened, on both sides of the car... I tried prying the shovel handle up a little farther. Nothing worked. I just could not get enough leverage to move the cross member. or tranny, over enough to make the stud pop in on the right side. It was easily within .125"! Many different tools and implements were use to help in the persuasion, to no avail. Then I thought if I only had a come - along...then I thought more and wondered if my very recent purchase from Harbor Freight would do the trick. I bought the ratcheting set of tie downs just the day before... I wrapper one around the butterfly bracket and the other end I fed around a handy deck support, 4X4.attached to the house. I started ratcheting and within 15 ratchets, I heard a comforting thunk from under the car. I crawled under it, tow rope still in place, taught, and saw that it had worked. The stud on the mount was in a hole, but it was the front hole, for OD transmissions. I grabbed the cross member where it bolts to the frame and pulled down, with almost no effort at all the stud came out of the bracket and with a slight move on the cross member, it went right in the rear hole. I then tightened the nuts onto the studs, via the holes I drilled in the cross member and made sure all was tight. Bolting the member back in place. I had new rear mounts! That kind of how I remember doing it... Good luck with yours...

Posted 2017-11-26 20:38:59 by Bill Schultz

ONE YEAR TO THE WEEK!

Sat, 11 Nov 2017 22:58:41 -0600

Bill Schultz's Journal --

Well, it was one year ago this week I bought and brought home my current 1974 B. I picked it up in Watervliet NY, just above Albany. The 80 plus miles to its new driveway was uneventful except for the awful noise of metal dragging on asphalt as we were passing through Stockbridge MA on the Mass Pike. Stan, the friend I hired to help me pick up the car with his car dolly, had the same look on his face as I did, thinking it was the drive shaft, exhaust system or worse when a please look cam over Stan's face. "I know what it is" he said with a smile as we pulled into the emergency lane. We both hopped out and he told me to stand on a part of the dolly, which immediately lifted it up and he bent over and inserted a oin in the hole supporting the pivot point on the dolly. "All set" he said and off we went to the final destination for this trip, my home. From Nove of 2016 until May of 2017, I dumped 2 pints each of Mystery Oil, Brake Fluid and a quart of acetone into the cylinders, hoping for the engine to UN-seize, Nothing worked, including pushing the car up the driveway with my Saturn Ion with the MG in 1st gear. The rear tires would drag of the right one would spin a little, which I could not imagine was anything good to be doing. Meanwhil, I sorted out minor electrical problems for the lights and started running new lines, replacing the rear shoes and calipers and pads up front. Right side is done still must get at the left side. In May I started planning on a rebuild of the engine and then I saw an ad on facebook on the MG Appreciation pages for a used, running 1800 from a 1975. Surprisingly, it was at a small MG shop just 30 miles from my place, I called Geoff and made a deal after confirming the compression was good. I was ready to pick it up when my left eye's Retina decided to let go. Emergency surgery and six weeks later, I was back at it. I picked up the motor and pulled the froze '74 and the tranny out of the car. I replaced clutch components and had the flywheel trued up. Swapped the face plate so the new mounts would fit the frame of the '74 and replaced the rear mount on the tranny. One of the more fun jobs to perform on these cars, but all was being re assembled and installed by October, I had also replaced the jets and seats and needles in the carbs. One of the carb, the front, was pretty tight as far as the piston movement in the vacuum dome. I sanded the edges of the poston and it seems to be free moving now. After installing the tranny and motor, I attached the battery and turned the key, Click, Click. That's what it did before I did all the work on it. You would think I would have had the started tested while it was out of the car for weeks, but noooo. So, I had to pull the started and replace it with one I got in less than 24 hours after ordering from O'Riely Auto Parts. Great store. I put the new starter in as the temps were hovering around 47 degree's. My goal was to have the MG running before the snow flies, oh, I do not have a garage. I installed the new starter, reattached the battery, turned the key and Whir...Whir went the engine. That wonderful sound of an MG motor sounded like the most wonderful thing I have heard in a long time...it is to THE WEEK that it turned over, one year before, when I bought the car and brought it home. Now, two day after the started being installed, November turned into February with 14 degree temps and wind chills to 4 degrees! When more seasonable temos return, I will finish attaching the overflow lines and other assorted lines under the hood, attache the lawn mower gas tank to the carbs and start the adjustments to get it running, Oh, the floors will be done in the spring, I started cutting them out in the summer...rusted through. Also the gas tank need a good examination and I will purchase a new fuel pump over the winter...Ah, but I just feel good that the engine turnds over and I am that much closer to going for a ride...

<IMG 0513>

Posted 2017-11-11 22:58:41 by Bill Schultz

Post From When I Owned My First '74.

Tue, 28 Mar 2017 20:43:02 -0500

Bill Schultz's Journal --

I have owned my MGB for since July 21 1998, ( my birthday). I have not had the time or space to do a complete restoration (long story) but intend to do so - someday. The car has run and given me minimal problems considering its age (and make). I did have a couple of rust spots, not the sills but forward of the wheel well on the rear quarter panels. I sanded and fiberglassed / bondoed those areas. The replacement parts include: New Master Brake Cylendar, New Kingpin - left side - need to do right side. As for me, I am a young fifty-ish, I am in the printing trade, which has had some ups and down in the current economy! As I said before, I hope to restore my car to the level of beauty found on this site. So many beautiful cars.... Thanks for reading, Bill

Posted 2017-03-28 20:43:02 by Bill Schultz

Mystery Oil Doesn't Do It

Wed, 30 Nov 2016 19:49:13 -0600

Bill Schultz's Journal --

Replaced engine with a "75

Posted 2016-11-30 19:49:13 by Bill Schultz

Another '74, YAHOO!

Thu, 24 Nov 2016 11:14:26 -0600

Bill Schultz's Journal --

Well, after selling my B a couple of years ago, I thought i felt some relief as it was always in the driveway, wishing I would drop $5000,00 on it and make it all better. But, the travel itch took hold and I sold the MG and my Bike and went to Paris for 10 days. It was a great trip and I have no regrets about selling the vehicles to folks who will definitely get more use out of them and give them the attention they need. So, a year went by, and another year, I started planning a trip to Italy, Egypt or Israel. But, I noticed I was watching, checking Craig's list and would inevitably enter MGB in the search window. This lead to a few emails going out, I really didn't have the cash but knew I was going to, eventually. Then a phone call here. Scheduled to look at one and it sold the day before I was going to see it. Then another. This one was an equal distance from my house, 80 miles, as was the other one, but this one didn't run. Actually, the engine is frozen. Anyway, I made the deal and my buddy with a dolly and a repair plate helped me get it home (For a mere $200.00) and now it resides in my drieway, looking like it would like me to drop $5000.00 on it to make it all well and pretty. This '74 is in a little better shape but needs some persistant care. Mystery Oil is working on the cylenders and I am slowly getting the electrical sorted out. New Alt and Coil ready to go in. Throw some wheel brake cylenders on the two read wheels and I will be ready for a ride in the Berkshire Hills sometime next summer....I hope! So glad to be back on this site too! I will keep you posted...

<00u0u lcyOy2eajTU 600x450>

Posted 2016-11-24 11:14:26 by Bill Schultz

British By The Sea

Sun, 07 Jun 2009 23:30:55 -0500

Bill Schultz's Journal --

A beautiful day, full sun, blue sky, and what must have been 250 british cards! I am trying to decide on a paint scheme and the colors were endless. What I thought was the rarest at the show was a couple of MG four door sedans, I am not sue of the model name but they were cool. There were thousands of spectatores, those who love british heritage automobiles are alive and well in Connecticut

Posted 2009-06-07 23:30:55 by Bill Schultz

Kingpins

Sat, 07 Mar 2009 22:09:36 -0600

Bill Schultz's Journal --

Well Its 3/07/09 and I have not made an entry since 07 by the looks of things. I have since put the new convertile top on, this was not as hard as I thought it was going to be. It only took a couple of hours, the only problem was withstretching the top over the top rail which attaches to the windshield. I did not get it perfectly straight and there is a small "pucker" on the driver side corner. Not too bad though.
I also replaced the right side kingpin. Another project which was not a bad as I thought, It did take a few weekends to accomplish as I was working outside and the weekend weather did not cooperate. I think it took two full days - maybe 16 hours or so, to replace, I also replaced the shock bumper and and the wheel bearings. This was in the summer of 07 - The car passes state ispection after the work was complete. I have just purchased a set of Kinkpins - off ebay - and will get into the left side kingpin this summer. ( I think) I am going to start accumulating the misc hardware to accomplish the project.
I purchased a new steering wheel and will put that on in the spring.
Back to the kingpin, I started a journal with the steps involved, and hope to publish it on this site when I finish the kingpin project.
Later

<MG logo>

Posted 2009-03-07 22:09:36 by Bill Schultz

The Beginning 5/26 2007

Sat, 26 May 2007 15:22:29 -0500

Bill Schultz's Journal --

Just as I am starting to begin my journal, My neighbor from downstairs knocks on my door and presents me with a bowl of homemade vanilla ICE CREAM. What a great way to start. My neighbor has also lived in Great Britain for a couple of decades so that is also a positive thing. I have finally moved my MGB to my home in just the last couple of weeks. It has been in storage, and I have finally retrieved the car from the ex's garage. I have owned it for 9, yes NINE years and only had it on the road, legally, for one summer. It never fails to start though, even when I neglect it for a full winter.
So far I have replaced:
Brake Cylanders
Brake Master Cylandar
Oil Pressure Line
Fuel Pump
Air filters (K&N)
Rear Lenses in tail lights
Windshield washer motor
Generator
Right hand mirror
I added a voltmeter
Much more to do, I am ready to put on a new vinyl top, it only has the hardtop now.
FRONT BUSHINGS. It failed a safety inspection because of "bad ball joints" little did I know it does not have ball joints! Tally HO! Onward I go!

Posted 2007-05-26 15:22:29 by Bill Schultz